Rotel RVE-1060 Owner's Manual download pdf (Page 17)

English

be analog audio connections using a pair

of standard RCA audio cables.

The various audio connections to a Rotel sur-

round sound processor are shown in Figures 6

and 7. See the Owners’ Manual for your sur-

round processor or A/V receiver for detailed

instructions on making these connections.

Other Connections

Computer I/O

The RVE-1060 can be operated from a com-

puter with audio system control software

from third-party developers. This control is

accomplished by sending operating codes

from the computer via a hard-wired RS-232

serial connection.

The COMPUTER I/O input provides the

necessary network connections on the back

panel, using the supplied Computer I/O

cable. Plug the 8-pin modular plug end of

the cable into the COMPUTER I/O connec-

tor. Plug the other end into a DB-9 serial port

on the computer.

For additional information on the connections,

software, and operating codes for computer

control of the RVE-1060, contact your autho-

rized Rotel dealer.

NOTE: This connection can also be used for

installing future updates to the RVE-1060

operating software. For upgrading, the UP-

GRADE option must be enabled in the Setup

menus. See the Setup section of the manual

for instructions.

AC Power

Your RVE-1060 will automatically conﬁgure

itself for the proper AC line voltage ranging

from 110 volts to 240 volts at 50/60Hz. No

setting is required to match the unit to your

local voltage.

Plug the supplied cord into the AC INPUT

receptacle on the back of the unit. After all

connections have been made, plug the cord

into an appropriate AC wall outlet.

NOTE: If you are away for an extended period

of time, it is a sensible precaution to unplug

your audio/video components.

EXT REM IN Jack

This 3.5mm jack receives command codes

from industry-standard infrared receivers via

hard-wired connections. This feature could

prove useful when the unit is installed in a

cabinet and the front panel sensor is blocked.

Connect this input to the EXT REM OUT jack

of the main Rotel component with a mono

3.5 mm to mono 3.5 mm cable.

12V TRIGGER Input

The RVE-1060 can be activated by a 12 volt

trigger signal from another Rotel component,

such as a surround processor. The 12V IN

connection provides an input to receive the

12 volt trigger signal.

The trigger input accepts any control signal

(AC or DC) ranging from 3 volts to 30 volts.

When the supplied cable is connected to

the input and a trigger signal is present, the

RVE-1060 is activated. When the trigger sig-

nal is interrupted, the unit goes into standby

mode. The front panel indicator light remains

lit, but the Input/Output LEDs are extinguished

and the unit will not operate.

Connect one end of the supplied cable to

the 12V TRIGGER INPUT on the RVE-1060.

Plug the other end into the 12V TRIG output

of the Rotel surround processor, receiver, or

preamp.

Connections to Rotel

Surround Sound

Processors and Receivers

See Figure 8

Once conﬁgured, the RVE-1060 handles all

video switching and processing, operated

automatically by a Rotel surround processor

or receiver. Select an input for listening on

the Rotel surround processor and the proces-

sor automatically commands the RVE-1060

to send the matching video signal to the TV

monitor. This quick start guide provides simple

instructions for integrating the RVE-1060 with

Rotel RSX-1056, RSX-1057, RSX-1067, RSP-

1068, RSP-1098, etc.

Connect a video monitor

1. Connect the video monitor or TV to the

RVE-1060. This can be any kind of video

monitor or connection, but will typically

be a high-deﬁnition digital monitor con-

nected to the HDMI monitor output of the

RVE-1060. No TV monitor is connected

to the surround processor.

2. Set the MONITOR INTERFACE setting on

the RVE-1060 MONITOR SETUP menu

to match the TV monitor (HDMI/DVI or

ANALOG).

Connect audio source inputs

1. Connect all audio signals from the source

input components (DVD player, HDTV re-

ceiver, etc.) to the audio inputs of the Rotel

surround processor or receiver. No audio

connections are made to the RVE-1060.

Connect video source inputs

1. Connect up to ﬁve video source input

components (DVD player, HDTV cable

receiver, etc.) to the video inputs of the

RVE-1060. No video sources are con-

nected to the surround processor.

2. If you have not connected the video sourc-

es to the default connections for the ﬁve

inputs on the RVE-1060, go to the INPUT

SETUP menu of the RVE-1060 and assign

each of the video sources to one of the

ﬁve inputs. The default assignments are:

Input 1: HDMI 1 connection

Input 2: HDMI 2 connection

Input 3: COMPONENT 1 connection

Input 4: S-VIDEO 1 connection

Input 5: COMPOSITE 1 connection

Connect the RVE-1060 to the

surround processor

1. Connect the RVE-1060 to the surround

processor with the supplied computer I/O

cable. Connect the 8-pin modular plug of

the cable to the COMPUTER I/O output of

the Rotel surround processor. Connect the

DB-9 Serial plug of the cable to the SERIAL

I/O connector on the RVE-1060.

2. Make a video connection between the

surround processor and the RVE-1060

using the supplied S-Video cable, so that

the on-screen menus from the surround

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 112 113

Comments to this Manuals

No comments

Rotel RVE-1060 Owner's Manual Page 17

Comments to this Manuals

Related products and manuals for Audio amplifiers Rotel RVE-1060