Rotel RSX-1058 Owner's Manual download pdf (Page 47)

English

• Component Video output at 720p or 1080i

may not be available if the source signal

includes HDCP copy protection.

• HDMI cables must be 5 meters or less in

length.

OSD menus are not displayed on TV

Monitor.

• In some PAL systems, the menus may not

be displayed unless there is an active

video signal.

Video and Audio do not match.

• Check that the proper video source is se-

lected for each input.

• Check that the group delay (lip-synch)

setting is not misadjusted.

Clicking or popping sounds when

switching inputs.

• The unit uses relay switching to preserve

maximum sound quality. The mechanical

clicking of the relays is normal.

• During switching, it may take a split sec-

ond for digital signals to be recognized

and properly decoded. Rapid repeated

switching between inputs or settings can

result in clicks or pops from the speakers as

the unit attempts to lock on to the rapidly

changing signals. This causes no harm.

Controls do not operate.

• Make sure that fresh batteries are installed

in the remote.

• Make sure that the IR sensor on the front

panel is not blocked. Aim the remote at

the sensor.

• Make sure the sensor is not receiving strong

IR light (sunlight, halogen lighting, etc.)

• Unplug the unit from the AC outlet, wait 30

seconds, and plug it back in to reset.

No video from Zones 2, 3 or 4

• Check ZONE SETUP conﬁguration and

zone video input setting as assigned and

make sure that a Composite source is con-

nected.

Speciﬁcations

Audio

Continuous Ampliﬁer Power

(ﬁve channels driven)

75 watts/ch (20-20k Hz, <0.05% THD, 8 ohms)

Continuous Ampliﬁer Power

(two channels driven)

100 watts/ch (1kHz, <1.0% THD, 8 ohms, DIN)

Total Harmonic Distortion

<0.09%

Intermodulation Distortion (60 Hz:7 kHz)

<0.05%

Frequency Response

10 Hz – 120 kHz, ±3dB (analog bypass)

10 Hz – 95 kHz, ±3dB (digital input)

Signal to Noise Ratio (IHF A-weighted)

95dB (analog bypass)

92dB (Dolby Digital, dts) 0dBFs

Input Sensitivity/Impedance

Line Level: 200 mV/100K ohms

Preamp Output Level/Output Impedance

1.0 V / 1K ohms

Contour (LF/HF)

±6dB at 50 Hz/15 kHz

Decodable Digital Input Signals

Dolby Digital, Dolby Digital EX, DTS, DTS-ES, DTS

96/24, LPCM (up to 192k), HDCD, MP3

Video

Input Resolutions

480i/576i, 480p/576p, 720p, 1080i

1080p (HDMI only)

Output Resolutions

480i/576i (Composite, S-Video only), 480p/576p,

720p, 1080i

1080p (HDMI only)

Signal to Noise Ratio

45dB

Input Impedance

75 ohms

Output Impedance

75 ohms

Output Level

1.0 volt

HDMI Input/Output :

Version 1.1

FM Tuner

Usable Sensitivity

14.2dBf

Signal to Noise Ratio (at 65dBf)

70dB

Harmonic Distortion (at 65dBf)

0.03%

Stereo Separation (1 kHz)

45dB

Output level

Antenna Input

75 ohms unbalanced

AM Tuner

Sensitivity

500μV/m

Signal to Noise Ratio

40dB

Output level

500 mV

Antenna Input

Loop Antenna

General

Power Consumption

450 watts

100 watts (idle)

4.7 watts (standby)

Power Requirements (AC)

120 volts, 60Hz (USA version)

230 volts, 50Hz (CE version)

Weight

17.4 kg/38.4 lb.

Dimensions (W x H x D)

432 x 162 x 442 mm

17.01” x 6.38” x 17.40”

Front Panel Height

(feet removed/for rack mount)

150 mm / 5.91”

When sizing openings in custom cabinets, mea-

sure the unit to be installed and/or allow at least

1 mm clearance on all sides for unit to unit toler-

ances.

All speciﬁcations are accurate at the time of print-

ing. Rotel reserves the right to make improve-

ments without notice.

Rotel and the Rotel HiFi logo are registered trade-

marks of The Rotel Co, Ltd., Tokyo, Japan.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 91 92

Comments to this Manuals

No comments

Rotel RSX-1058 Owner's Manual Page 47

Comments to this Manuals

Related products and manuals for DVD players Rotel RSX-1058