Rotel RSX-1058 Owner's Manual download pdf (Page 36)

RSX-1058 Surround Sound Receiver

4. If no station is located for the desired con-

tent type, the tuner will return to the last

previously tuned station.

5. Cancel the PTY function by pressing any

other button.

NOTE: If the currently tuned station is broad-

casting PTY data, a PTY indicator lights in the

front-panel display.

TP Button

Searches for an RDS station broadcasting

trafﬁc information programming:

1. Press the TP button. The tuner attempts to

ﬁnd an RDS station broadcasting the traf-

ﬁc programming. If a station is found, a

TP indicator lights in the front-panel dis-

play.

2. If no station is located, the tuner will re-

turn to the last previously tuned station.

3. Cancel the TP function by pressing any

other button.

TA Button

Searches for an RDS station broadcasting

special trafﬁc announcements:

1. Press the TA button. The tuner will attempt

to ﬁnd an RDS station broadcasting traf-

ﬁc announcements.

2. If no station is located, the tuner will re-

turn to the last previously tuned station.

3. Cancel the TA function by pressing any

other button.

Zone 2–4 Operation

The RSX-1058 provides Zone 2–4 multi-room

capability, allowing you to enjoy music and

operate the system from up to three addi-

tional rooms or ‘zones’. From these remote

locations, you can select a source compo-

nent (independent from the source playing

in the main room), adjust the volume level

in the remote zone, and operate the source

components.

To use the Zone 2–4 capability, you need

additional components: a pair of speakers

installed in the remote zone, an ampliﬁer

to drive them, an optional TV monitor for

video signals, and a third-party IR repeat-

er system.

Zones 2–4 can be controlled from the main

room using RSX-1058’s front-panel SEL or

remote control REC button. Operation from

the remote zone or zones requires the instal-

lation of an infrared repeater system (Xan-

tech, Niles, etc.) which relays infrared remote

control commands from Zone 2, 3 or 4 to

the speciﬁc ZONE REM IN connector on the

back of the RSX-1058.

Several points to keep in mind about the

Zone 2–4 function:

• There are two options for output level, se-

lectable from the OSD conﬁguration menu.

VARIABLE output provides full adjustment

of the volume level. FIXED output disables

the Zone 2, 3 or 4 volume control with the

output permanently set to a speciﬁed level.

This might be useful for sending a line level

signal to a preamp or integrated amp with

its own volume control or to a distribution

ampliﬁer with multiple volume controls.

• The RR-1060 remote control supplied with

the RSX-1058 will operate Zone 2, 3 or

4 if used with a repeater system from the

remote zone. It can also be programmed

to operate Rotel source components via

the RSX-1058’s IR OUT jack.

• Any source component connected to the

RSX-1058’s analog inputs can be sent

to the Zone 2, 3 or 4 outputs. ZONE 2,

ZONE 3 and ZONE 4 operate indepen-

dently of the main room. You can select

a different source or adjust Zone 2, 3 or

4 volume from each zone without affect-

ing the MAIN outputs in any way.

• Avoid sending the same infrared com-

mand to the RSX-1058 front-panel sen-

sor and a Zone 2, 3 or 4 repeater at the

same time. This means that Zones 2, 3

or 4 must be in a different room from

the RSX-1058.

Zone 2–4 Power On/Off

Once master power is applied to the unit

by pressing the rear panel POWER switch

button, the RSX-1058 provides independent

power on/off operation for all zones. Press-

ing the remote control ON/OFF buttons in

the main room activates or deactivates the

RSX-1058 in the main room only and has no

effect on Zone 2, 3 or 4. Conversely, acti-

vating or deactivating Zone 2, 3 or 4 has

no effect on the main listening room. How-

ever, placing the rear panel master POWER

switch in the OFF position completely shuts

off the unit, for all zones.

NOTE: For proper power on and off operation

with Zones 2–4, the RSX-1058’s power mode

should be set to the factory default STANDBY

setting or to the DIRECT setting using the Other

Options menu described in the Setup section

of this manual.

Controlling Zones 2–4

from the Main Room

You can control Zones 2–4 from the main room

using front-panel or remote control buttons

to activate or deactivate Zones 2–4, change

input sources, and adjust the volume. Con-

trolling Zone 2, 3 or 4 from the main room is

accomplished by pressing the SEL button on

the front panel or REC button on the remote

two or more times, putting the RSX-1058 in

Zone 2, 3 or 4 control mode temporarily.

When Zone 2, 3 or 4 status is displayed,

the OSD and/or front-panel displays show

the current source selection and volume in

that zone for ten seconds, during which time

you can use the front panel VOLUME control

and INPUT buttons to change the ZONE 2,

3 or 4 settings.

To turn Zone 2, 3 or 4 on or off:

1. Press the front panel SEL or remote REC

button repeatedly until the desired zone

status appears in the OSD and front panel

displays.

2. Within 10 seconds, press the front panel

or remote ZONE button to toggle the se-

lected Zone on or off.

3. Following 10 seconds with no commands,

the RSX-1058 reverts to normal opera-

tion.

To change the Zone 2, 3 or 4 input

source:

1. Press the front panel SEL or remote REC

button repeatedly until the desired zone

status appears in the OSD and front panel

displays.

2. Within 10 seconds, press one of the IN-

PUT buttons to select a new source for the

selected zone. The name of the selected

source appears in the display. Instead of

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 91 92

Comments to this Manuals

No comments

Rotel RSX-1058 Owner's Manual Page 36

Comments to this Manuals

Related products and manuals for DVD players Rotel RSX-1058