Rotel RSX-1058 Owner's Manual download pdf (Page 26)

RSX-1058 Surround Sound Receiver

RDS/RBDS Buttons

Four remote control buttons (DISP, PTY, TP, TA)

are used to activate various RDS/RBDS tuning

features. See the RDB/RBDS Tuning section of

the manual for detailed information.

Basic Operations

This section covers the basic operating con-

trols of the RSX-1058 and the remote.

Power and Standby On/Off

The rear panel POWER switch on the RSX-1058

is a master power switch. The button must

be in the ON position for the unit to oper-

ate. When it is in the OFF position, the unit

is fully off and cannot be activated from the

front panel or remote control.

In normal operation, the rear panel POWER

switch is always left in the ON position. The

RSX-1058 is activated and deactivated using

the front-panel STANDBY button, the remote

control POWER button, or the remote ON/

OFF buttons. When activated, the RSX-1058

is fully functional and the front-panel display

illuminated. When deactivated, the unit goes

into a standby mode, with minimal power ap-

plied to the microprocessor.

NOTE: When the unit has AC power ap-

plied and the rear panel POWER switch is on,

the front-panel STANDBY LED lights, regard-

less of whether the unit is in standby mode or

activated.

The front-panel STANDBY button and the re-

mote control POWER button function as tog-

gle switches. Press either button to activate

the unit. Press either button again to put the

unit in standby mode.

The ON/OFF buttons on the remote serve

the same function, but provide discrete ON

(active) or OFF (standby) commands.

NOTE: When using the Zone room capabil-

ity of the RSX-1058, the standby activation is

completely independent for the main room and

the zones. ON/OFF commands sent from the

remote in the main room will not affect Zones

2–4. Pressing the ON/OFF buttons on a remote

located in Zone 2, 3 or 4 will only affect that

zone and not the main room. When the unit is

activated in one of the zones, that zone’s icon

is lit in the front-panel FL display.

There are four available power mode op-

tions, which may be useful in conﬁguring the

RSX-1058 for special system conﬁgurations.

See the Other Options menu in the Setup sec-

tion of this manual for additional details on

changing the default standby behavior.

‘Resume’ retains the last power conﬁgura-

tion when the main power is switched OFF

and then switched ON again. For example,

if the RSX-1058 is in operation and the main

power is switched OFF, when the main power

is switched ON, the unit will be in operation

mode again.

All OFF command: A long press of the

OFF button (more than 3 seconds), from any

room, sets the RSX-1058 to standby.

Volume Adjustments

The listening volume of the RSX-1058 can be ad-

justed from the front panel or the remote.

Front Panel: Rotate the front-panel VOL-

UME knob clockwise to increase the volume,

counterclockwise to decrease.

Remote: Press the VOL UP button to in-

crease the volume; press the VOL DOWN

button to decrease.

When you adjust the volume, the setting

is shown on the SDTV monitor and/or the

front-panel display. The current volume set-

ting is also shown on the SYSTEM STATUS

OSD screen.

NOTE: The VOLUME controls can be used to

change the volume in Zone 2, 3 or 4. Press

the front-panel or remote control ZONE button

and adjust the volume. After 10 seconds, the

VOLUME control reverts to normal operation.

Muting the Sound

The volume of the RSX-1058 can be turned off

or muted. Push the MUTE button on the front

panel or the remote once to turn the sound

off. A MUTE indication appears in the OSD

and the front-panel displays. Press the MUTE

button again or adjust the volume settings to

restore output levels.

Selecting Inputs

Input Buttons

You can select any of nine source inputs for

listening and/or watching: CD, TUNER, TAPE,

VIDEO 1, VIDEO 2, VIDEO 3, VIDEO 4, VID-

EO 5, or MULTI INPUT (EXT on remote).

The front-panel display and the ON-SCREEN

DISPLAY show the name of the current listen-

ing source selection. The labels for VIDEO

sources can be customized to match your

components.

NOTE: When the TUNER input source button

is pressed, the frequency of the currently tuned

station is displayed. Pressing the button again

toggles the display to show the word TUNER

instead of the frequency display.

All of the source inputs can be customized us-

ing the ON-SCREEN DISPLAY conﬁguration

menus to accept either analog signals or digi-

tal signals from one of the seven assignable

digital inputs, or HDMI Audio. When a digi-

tal input is assigned, the RSX-1058 checks for

the presence of a digital signal at that input.

If a digital signal is present when the source

is selected, it is automatically activated and

the proper surround mode enabled. If no

digital signal is present, the analog inputs

for that source are selected. This auto-sens-

ing is the preferred conﬁguration for digital

source inputs such as DVD players. When

an ANALOG input is assigned, the unit will

not access a digital signal, even though one

may be available at the digital input.

By default, the source input buttons are factory

conﬁgured to select the following inputs:

CD: Digital Coaxial 2

Tuner: Analog (built-in)

Tape: Digital Coaxial 3

Video 1: HDMI Audio (HDMI 1)

Video 2: HDMI Audio (HDMI 2)

Video 3: Digital Optical 1

Video 4: Digital Optical 2

Video 5: Digital Coaxial 1

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 91 92

Comments to this Manuals

No comments

Rotel RSX-1058 Owner's Manual Page 26

Comments to this Manuals

Related products and manuals for DVD players Rotel RSX-1058