Rotel RSX-1058 Owner's Manual download pdf (Page 19)

English

NOTE: HDTV Component Video output is

subject to HDCP copy protection. It may not

display 720p or 1080i resolution when the

source signal incorporates copy protection.

However, when Video Out is set to 480p/576p

in the VIDEO/HDMI menu, all sources will be

available. Component Video output is not avail-

able for 480i/576i images.

NOTE: Do not connect HDMI and Compo-

nent Video outputs to a monitor simultane-

ously, as the two video image signals may

affect each other.

HDMI connections:

• The RSX-1058 uses the HDMI Ver. 1.1

standard. TV monitors with HDMI inputs

should be compatible with this version.

• The video signal sent to the TV through the

HDMI connection will not be displayed

properly unless all HDMI components in

the system, including the TV monitor, are

compatible with the HDCP copy protec-

tion standard.

• Only audio signals passed-through directly

from the source component are sent to the

TV set through the HDMI connection. To

send decoded audio from the RSX-1058

to the TV, you must select ‘TV mode’ in

the VIDEO/HDMI menu.

• TV monitors with DVI-D connections can

usually be connected to the HDMI out-

put of the RSX-1058 with the use of an

appropriate 24-pin DVI-HMDI adaptor.

However, there are occasionally some in-

compatibilities with older DVI-D equipped

monitors.

• Use the scaler setting of the RSX-1058

‘VIDEO OUT FORMAT’ in the VIDEO/

HDMI menu to match the natiive resolu-

tion of the TV monitor.

• In general, HDMI is the optimum connec-

tion for digital high-deﬁnition monitors

such as LCD, plasma, or DLP monitors.

NOTE: Do not connect HDMI and Compo-

nent Video outputs to a monitor simultane-

ously, as the two video image signals may

affect each other.

ZONE OUT Video Outputs

The ZONE OUT Video outputs of the RSX-1058

send a Composite video signals to TV moni-

tors in Zone 2, 3 & 4.

NOTE: Only Composite video input signals are

available at the Zone 2, 3 & 4 video outputs.

Digital Audio

Input & Outputs

The RSX-1058 provides digital connections

which may be used in place of, or in addition

to, the analog audio input and output con-

nections described in the previous sections.

These connections include seven digital inputs

and also an HDMI Audio digital input. and

two digital outputs (for recording),

These digital connections can be used with

any source component that supplies a digi-

tal signal, such as a DVD player, CD player,

or satellite TV tuner.

NOTE: With a digital connection, the RSX-1058

will be used to decode the signal, rather than

the source component’s internal decoders. In

general, you must use digital connections for a

DVD player or other component that supplies

a Dolby Digital or DTS signal; otherwise the

RSX-1058 will not decode these formats.

Digital Inputs

The RSX-1058 accepts digital inputs from

source components such as CD players, sat-

ellite TV tuners, and DVD players. The built-

in digital processor senses and adjusts to the

correct sampling rates.

There are seven digital inputs on the rear

panel, three coaxial and four optical, as well

as HDMI Audio input. These digital inputs

can be assigned to any of the input sources

using the INPUT SETUP screen during the

setup process. For example, you can assign

the COAXIAL 1 digital input connector to the

VIDEO 1 source and the OPTICAL 2 digital

input to the VIDEO 3 source. By default, the

source input buttons are factory conﬁgured

to select the following inputs:

CD: Digital Coaxial 2

Tuner: Analog (built-in)

Tape: Digital Coaxial 3

Video 1: HDMI Audio (HDMI 1)

Video 2: HDMI Audio (HDMI 2)

Video 3: Digital Optical 1

Video 4: Digital Optical 2

Video 5: Digital Coaxial 1

NOTE: When using digital connections, you

should also make the analog audio input con-

nections described previously. The analog con-

nection is necessary to record to an analog

recorder in some circumstances or for ZONE

2, 3 & 4 operation.

Digital Outputs

The RSX-1058 has two digital outputs (one

coaxial and one optical) to send the digital

signal from any of the digital inputs to a dig-

ital recorder or outboard digital processor.

When a digital input source signal is selected

for listening, that signal is automatically sent

to both digital outputs for recording.

NOTE: Only digital signals from source com-

ponents are available at these outputs. Analog

signals cannot be converted and are not avail-

able at the digital outputs.

Other Connections

AC Input

Your RSX-1058 is conﬁgured at the factory

for the proper AC line voltage in the country

where you purchased it (USA: 120 volts/60Hz

AC or CE: 230 volts /50 Hz AC ). The AC

line conﬁguration is noted on a decal on the

back of your unit.

Plug the supplied cord into the AC INPUT re-

ceptacle on the back of the unit.

NOTE: Memorized settings and video labels

are preserved indeﬁnitely, even if the RSX-1058

is disconnected from AC power.

Master Power Switch

The large rocker switch on the rear panel is

a master power switch. When it is in the OFF

position, power to the unit is completely off.

When it is in the ON position, the front-panel

STANDBY and remote control ON/OFF but-

tons can be used to activate the unit or put it

into standby mode.

NOTE: After all connections are completed,

the rear panel master power switch should

be put in the ON position and usually left in

that position.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 91 92

Comments to this Manuals

No comments

Rotel RSX-1058 Owner's Manual Page 19

Comments to this Manuals

Related products and manuals for DVD players Rotel RSX-1058