Rotel RSX-1058 Owner's Manual download pdf (Page 21)

English

the same video input source used above. If an

HDMI connection is used, assign HDMI Audio

for the digital audio, or one of the OPTICAL

IN or COAXIAL IN digital inputs.

Analog audio connections:

If you want to record the audio signal from

the DVD player or distribute the audio signal

to Zones 2–4, connect the left and right ana-

log outputs from the DVD player to the left

and right AUDIO IN jacks corresponding to

the VIDEO IN input selected above.

Cable, Satellite, HDTV Tuner

See Figure 8

Standard Deﬁnition TVs:

In a system with a standard deﬁnition TV,

cable or satellite tuner connections can be

made to the VIDEO 1, 2, 3, 4, or 5 inputs.

You may wish to use assigned Video Inputs

with interlace picture. The video picture is

then available by the assigned Video Input.

The analog audio is the same as the input

labelled terminals.

The video setting in each video source is by

assignment, so the INPUT labels of VIDEO 1-5

do not relate to video terminal numbers.

It is possible to assign any type of video ter-

minals, from the available three Composite

Video, three S-Video, three Component Vid-

eo and four HDMI.

If the monitor used is SDTV, an interlace source

(480i/576i) should be used.

NOTE: If you plan to distribute video from the

tuner to a TV monitor in Zone 2, 3 or 4, you

must make a composite video connection.

High Deﬁnition TVs:

It is possible to connect any video input for

use with an HDTV monitor, as the RSX-1058

has a built-in video converter and scaler in-

side. However, the higher the resolution of

the input signal, the higher the quality of

the picture.

With a high-deﬁnition cable or satellite tuner

and an HDTV monitor, you should use Com-

ponent Video and/or HDMI video connec-

tions from the tuner. If the tuner has a DVI-D

output, this can usually be connected to the

HDMI input on the RSX-1058 using a DVI-

HDMI adapter.

Connect a set of Component Video cables

or an HDMI cable from the tuner to the ap-

propriate input on the RSX-1058.

Digital Audio connections:

Connect the digital output of the tuner to

any one of the OPTICAL IN, COAXIAL IN

or HDMI IN digital inputs on the RSX-1058.

Use the INPUT SETUP screen to assign that

digital input to the same video input source

used above. For example, if you use the Vid-

eo 4 inputs above, assign the digital input to

the HDMI IN 1 input.

Analog audio connections:

If you want to record the audio signal from

the tuner to a VCR or distribute the audio sig-

nal to Zones 2–4, connect the left and right

analog outputs from the DVD player to the

left and right AUDIO IN jacks corresponding

to the VIDEO IN input selected above.

Audio Recorder

See Figure 11

Connect the left and right analog outputs from

an audio tape deck to the AUDIO IN jacks

labeled TAPE IN (left and right).

Connect the left/right AUDIO OUT/TAPE OUT

jacks to the inputs on the audio tape deck.

Optional: For a digital recording device,

connect the digital output of the recorder to

one of the OPTICAL IN or COAXIAL IN dig-

ital inputs on the RSX-1058. Use the INPUT

SETUP screen to assign that digital input to the

TAPE source. If the recording device accepts

a digital recording input, connect either the

OPTICAL OUT or COAXIAL OUT connection

to the digital input of the recorder.

No video connections are required for an

audio recording device.

VCR or Digital Video Recorder

See Figure 9

VCR connections can be made to the VID-

EO 1, VIDEO 2, or VIDEO 3 inputs and out-

puts. If you choose VIDEO 1, make sure that

you use either Composite or S-Video inputs

and outputs for all analog audio and video

connections.

Connect video cables (Composite Video,

S-Video, and/or Component Video) from the

output of the VCR to the appropriate video

input which is assigned.

Connect video cables (Composite Video

and/or S-Video) from the VIDEO OUT jacks

to the VCR inputs.

Connect the left and right analog outputs

from the VCR to one pair of the AUDIO IN

jacks labeled VIDEO 1–3.

Connect the left and right AUDIO OUT

jacks for VIDEO 1–2 to the analog inputs

on the VCR.

Optional: For a digital recording device,

you can use digital audio connections. Con-

nect the digital output of the recorder to one

of the OPTICAL IN or COAXIAL IN digital

inputs on the RSX-1058. Use the INPUT SET-

UP screen to assign that digital input to the

VIDEO source (VIDEO 1, 2, or 3) used for

the previous connections. If the recording

device accepts a digital recording input,

connect one of the OPTICAL OUT or CO-

AXIAL OUT connections to the digital input

of the recorder.

DVD-A or SACD Player

See Figure 7

To hook up a DVD-A, a SACD player, or any

external surround decoder, use audio RCA

cables to connect the outputs of the player to

the RCA jacks labeled MULTI INPUT, making

sure that you observe proper channel consis-

tency, i.e. connect the right front channel to

the R FRONT input, etc. Depending on your

system conﬁguration, make six connections

(FRONT L & R, SURROUND L & R, CENTER,

and SUBWOOFER), seven connections (add-

ing a CENTER BACK connection), or eight

connections (adding two CENTER BACK

connections).

The MULTI inputs are analog bypass inputs,

passing signals directly through to the Vol-

ume Control and preamp outputs, bypassing

all of the digital processing. The RSX-1058

provides an optional bass redirect feature

that duplicates the seven main channels and

passes them through an analog 100 Hz low

pass ﬁlter, creating a summed mono sub-

woofer output derived from the main chan-

nels. See the INPUT SETUP menu in the Set-

up section of this manual for details on bass

redirect feature.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 91 92

Comments to this Manuals

No comments

Rotel RSX-1058 Owner's Manual Page 21

Comments to this Manuals

Related products and manuals for DVD players Rotel RSX-1058