Rotel RSP-1066 Owner's Manual download pdf (Page 25)

SYSTEM STATUS Menu

SYSTEM STATUS

LISTEN: Tuner

RECORD: VIDEO 1

MODE: Stereo

INPUT: Analog

VOLUME: 45

ZONE: Off

ENT KEY=MAIN MENU

OSD KEY=EXIT

The SYSTEM STATUS menu provides a snap-

shot of the current system settings and a start-

ing point for reaching all other screens and

menus. This screen appears when you press

the MENU button on the remote control and

displays the following information:

LISTEN: the source selected for listening.

RECORD: the source selected for the VIDEO

and AUDIO outputs.

MODE: the current surround sound mode.

INPUT: the input selected for the current source:

Optical, Coaxial, Analog, etc.

VOLUME: the current volume setting.

ZONE: the current status of ZONE 2, ON or

OFF.

No changes can be made using this screen;

it only provides information. To go to the rest

of the menus, press the ENTER button to go

to the MAIN menu. Press the MENU key on

the remote to cancel the display and return

to normal operation.

NOTE

: The SYSTEM STATUS screen appears

for ten seconds when the unit is turned on

and automatically turns off.

MAIN Menu

MAIN MENU

INPUT SPEAKER

DELAY TEST TONE

SUB LEVEL ZONE 2

OTHER DEFAULT

ENT KEY=ENTER

UP KEY=up DWN KEY=down

The MAIN menu provides access to eight other

screens and menus and is reached by press-

ing the ENTER button from the SYSTEM STA-

TUS menu described above or from most other

menus. To go to another menu, move the high-

light to the desired line using the UP/DOWN

buttons on the remote and press the ENTER

button. Press the MENU key on the remote to

cancel the display and return to normal op-

eration.

INPUT SETUP Menu

INPUT SETUP

LISTEN: Video 2

INPUT LABEL: _ _ _ _ _

INPUT: Coaxial 2

SURR MODE: Dolby 3 Stereo

ENT KEY=MAIN MENU UP KEY=up

+/– KEY=change DWN KEY=down

The INPUT SETUP menu configures the source

inputs and is reached from the MAIN menu.

The screen provides the following options, se-

lected by placing the highlight on the desired

line using the UP/DOWN buttons:

LISTEN: changes the current listening input

source (CD, TUNER, TAPE, VIDEO1, VIDEO2,

VIDEO3, VIDEO4, VIDEO5).

INPUT LABEL: The labels for the five VIDEO

inputs can customized (not available for the

TUNER, CD, and TAPE inputs). Place the high-

light on this line to call up a sub-menu that al-

lows you to change the five-character label

for the current VIDEO source. To change the

label:

1. Press the +/– keys to begin labeling.

2. Press the +/– keys to change the first let-

ter, scrolling through the list of available

characters.

3. Press the ENT key to confirm that letter and

move to the next position.

4. Repeat steps 2 and 3 until all five charac-

ters have been completed. The final press

of the ENT button will save the new label

and exit the sub-menu.

INPUT: selects which physical input connec-

tion to use as the default for the source dis-

played in the first line of the menu. The op-

tions are ANALOG inputs, two OPTICAL digital

inputs (OPTICAL 1& 2), and three COAXIAL

digital inputs (COAXIAL 1 – 3). When a digi-

tal input is selected, the unit will check for a

digital signal when the INPUT SOURCE but-

ton is pressed. If no digital signal is present,

the unit will automatically revert to the ana-

log input. When an ANALOG input is selected,

the unit will not access a digital signal, even

though one may be present at the digital in-

put; thus, the ANALOG setting forces the unit

to use accept only an analog signal. Assign-

ing a digital input (with its auto-sensing) is the

preferred configuration for digital source in-

puts such as DVD players.

NOTE

: If a source connected to a digital input

is selected, that signal will automatically be

sent to both digital outputs for recording.

SURR MODE: selects the default surround

sound mode for the input shown at the top of

the menu. The default setting will be used unless

the source material triggers automatic decoding

of a particular type or unless the default set-

ting is overridden by the front panel or remote

surround buttons. Options are: Stereo, Dolby

Pro Logic II, Dolby 3-Stereo, Music 1 – 4, 5CH

Stereo, 7CH Stereo, and DTS Neo:6.

This is a default setting for each input and, in

some cases, can be manually overridden by

the front-panel MODE buttons or the SUR+

button on the remote. See the SURROUND

SOUND CONTROLS section of this manual

for more information on which settings can be

overridden.

NOTE

: The following types of discs or source

material are generally detected automatically

and the proper decoding activated with no

action or setting required: DTS, DTS-ES Ma-

trix 6.1, DTS-ES Discrete 6.1, Dolby Digital,

Dolby Digital Surround EX, Dolby Digital 2-

channel, PCM 2-Channel, MP3, and HDCD.

English

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 75 76

Comments to this Manuals

No comments

Rotel RSP-1066 Owner's Manual Page 25

Comments to this Manuals

Related products and manuals for AV receivers Rotel RSP-1066