Rotel RSX-1562 Owner's Manual download pdf (Page 46)

RSX-1562 SURROUND SOUND RECEIVER

1562. This allows the audio from the TV to be played through your

hometheater system.

Note: When ARC is enabled, the Rotel unit will play the audio from

the TV. The volume can be controlled by the TV’s remote control.

Note: When HDMI control is ON, the unit will pass HDMI Video and

Audio signals in Standby mode direct to the TV. The Rotel unit do not

have to be powered on if you only want to use the speakers of the TV

for audio. But the Rotel unit must be set to the correct input prior to

standby.

POWER CONTROL: Options are Yes, No. Selecting Yes, allows

other HDMI enabled units in your system to turn the RSX-1562 on or

off. In normal operation, powering ON the source will also turn on the

RSX-1562 and the TV. Turning the TV off, will turn off the RSX-1562

and the source.

Note: For power control to operate, all components in the system must

have power control enabled from source to displays. Although the unit

has been tested with most major brands of displays and sources, there

may still be occasional compatibility problems.

Zone 2-4 Setup

Z O N E S E T U P

M A I N M E N U

Z O N E : Z O N E 2

S O U R C E : C D

V I D E O I N P U T : C o m p o s i t e 1

V O L U M E S E T U P : V a r i a b l e

V O L U M E : 6 0

T U R N O N V O L : L a s t

M A X V O L : M a x

1 2 V T R I G G E R : 1 _ 3 _ _ _

The ZONE SETUP menu provides settings and conﬁguration options related

to the operation of the remote zones. This menu is reached by highlighting

the ZONE line on the MAIN menu and pressing ENT.

ZONE: Speciﬁes the zone to conﬁgure, ZONE 2, 3, or 4. Each zone

is conﬁgured individually.

SOURCE: Speciﬁes a source for listening in the selected zone. Options

are CD, TUNER, VIDEO 1-6, SOURCE, and OFF. Selecting the SOURCE

option links the zone source to the source selected for the main zone

so that the remote zone will hear the same source as the main zone.

Selecting the OFF option turns the zone off.

VIDEO INPUT: Speciﬁes a video source (Composite Video only) for the

selected zone. The options available are Composite 1, 2 and OFF.

VOLUME SETUP: Conﬁgures the remote zone outputs for VARIABLE or

FIXED volume levels. VARIABLE allows control of the volume settings in the

remote zone from the RSX-1562’s front panel or from a remote control/IR

repeater in the zone. FIXED output disables the volume control. In this

mode, the remote zone level can be ﬁxed at the level speciﬁed on the

next line, thus optimizing system performance when sending a ﬁxed level

signal to a preamp or ampliﬁer with its own volume adjustment.

VOLUME: In VARIABLE output mode, this line shows the current volume

setting for remote zone. In FIXED output mode, this volume setting

establishes a permanent ﬁxed output level for the remote zone

TURN ON VOL: Speciﬁes a default volume level to be used each time the

remote zone is activated. You can select LAST to have the zone activate

with the last previously used volume setting. Or, you specify a volume

from MIN (full mute) to MAX, in 1dB increments. Note that this setting

can not exceed the MAX VOL established in the next line of the menu.

MAX VOL: Speciﬁes the maximum volume level for the remote zone.

The volume cannot be adjusted above this level. Settings range from

MIN to MAX in 1dB increments.

12V TRIGGER: The RSX-1562 has six 12V trigger outputs (labeled

1–6) that supply a 12V DC signal to turn on Rotel components and other

components as needed. This menu item turns on speciﬁc 12V trigger

outputs whenever the indicated zone is activated. The six 12V Trigger

outputs may be assigned to each zone and can send a turn-on signal

to remote components whenever the remote zones are activated. For

example, ZONE 2 could use 12V Triggers 1, 3 and 6; ZONE 3, 12V

Triggers 2 and 3; ZONE 4, 12V Triggers 5 and 6.

Press the Left/Right buttons on the remote to change the ﬁrst position 1.

from blank to 1 (activating TRIGGER 1 for that zone).

Press the ENT button on the remote to move to the next position.2.

Repeat until all six positions are set as desired. A ﬁnal press of the 3.

ENT button conﬁrms the selection.

Default Setup

D E F A U L T S E T U P

F A C T O R Y D E F A U L T : N o

U S E R D E F A U L T : N o

S E T U S E R D E F A U L T : N o

S E T N E W P A S S WO R D : N o

MA I N M E N U

The DEFAULT SETUP menu provides access to six functions:

Set the tuning function for North America or European •

frequencies.

Redirect the Front channel ampliﬁers or the Center Back channel •

ampliﬁers to power remote speakers in Zone 2, 3 or 4, or redirect

the Center Back channel ampliﬁers to “Front” for bi-amping.

Restore all features and settings to the original FACTORY DEFAULT •

settings.

Memorize a custom group of settings as a USER DEFAULT.•

Activate the memorized USER DEFAULT settings.•

Set a NEW PASSWORD for the memorized USER DEFAULT •

settings.

To change the TUNER setting: Place the highlight on the TUNER setting

line using the Up/Down buttons and use the Left/Right buttons to change

the setting to N. AMERICA or EUROPE. Then, move the highlight to

the FACTORY DEFAULT line and change the setting to YES, using the

1 2 ... 41 42 43 44 45 46 47 48 49 50 51

Comments to this Manuals

No comments

Rotel RSX-1562 Owner's Manual Page 46

Comments to this Manuals

Related products and manuals for AV receivers Rotel RSX-1562