Rotel RSX-1562 Owner's Manual download pdf (Page 24)

RSX-1562 SURROUND SOUND RECEIVER

DVD or Blu-ray player and TV tuner connections can be made using

HDMI, Component Video, or Composite video connections.

Note: You must use either HDMI or Component Video connections for

a progressive scan or high deﬁnition player. You must make an analog

audio connection if you want to send signals to Zone 2,3 & 4.

For HDMI connections: Connect an HDMI cable from the output of the

Blu-ray player to one of the HDMI IN 1–6 inputs on the receiver.

For Component Video connections: Connect a set of three Component Video

cables from the output of the DVD player to one of the COMPONENT

VIDEO 1–2 inputs on the receiver . Make sure to connect the Y output to the

Y input, the PB output to the PB input, and the PR output to the PR input.

For Composite Video connections: Connect an RCA-RCA video cable

from the output of the DVD player to one of the COMPOSITE IN 1–2

inputs on the receiver.

Note: Use the INPUT SETUP screen to assign the video input you have

used to the Blu-ray source.

Digital audio connection: Connect the digital output of the DVD player

to any one of the DIGITAL IN OPTICAL 1–4 or DIGITAL IN COAXIAL

1–3 inputs on the receiver. An HDMI cable carries both digital

video and digital audio signals; therefore, no separate digital audio

connection needs to be made.

Note: Use the INPUT SETUP screen to assign the digital input to the

same video input source used above.

Optional analog audio connection: If you want to record the audio signal

from the DVD player, connect the left and right analog outputs from the

DVD player to one pair of VIDEO IN 1–6 audio input jacks. Make sure

that you connect the right channel to the R input jack and the left channel

to the L input jack.

Connecting DVD-A or SACD Player

See Figure 6

In most cases, DVD-A, SACD, and other external multichannel receivers

are connected to the receiver by sending decoded analog audio signals

using RCA cables. A DVD-A player with HDMI outputs can send digital

signals directly to the receiver for decoding.

Analog Connections: To hook up a DVD-A, an SACD player (or any external

surround decoder) with analog connections, use audio RCA cables to

connect the outputs of the player to the RCA jacks labeled MULTI INPUT,

making sure that you observe proper channel consistency, i.e. connect

the right front channel to the FRONT R input, etc.

Depending on your system conﬁguration, make six connections (FRONT L

& R, SURROUND L & R, CENTER, and SUBWOOFER), seven connections

(adding a CENTER BACK connection), or eight connections (adding two

CENTER BACK or Vertical Height connections).

The MULTI inputs are analog bypass inputs, passing signals directly

through to the Volume Control and preamp outputs, bypassing all of

the digital processing. The receiver provides an optional bass redirect

feature that duplicates the seven main channels and passes them through

an analog 100 Hz low pass ﬁlter, creating a summed mono subwoofer

output derived from the main channels. See the INPUT SETUP menu in the

Setup section of this manual for details on bass redirect feature.

HDMI digital connection: If the DVD-A player has HDMI outputs, simply

connect an HDMI cable to the output of the player to one of the HDMI 1–6

inputs on the receiver. This cable sends the video signal from the player

along with a digital audio signal. The DVD-A multichannel decoding is

handled by the receiver.

Connecting Video Recorder

See Figure 7

VCR connections can be made to any VIDEO inputs.

Composite connections: Connect an RCA video cable from the output of

the VCR to the COMPOSITE IN 1 input. Connect an RCA video cable

from the COMPOSITE OUT jack to the VCR inputs.

Audio Connections: Connect the left and right analog outputs from the

VCR to the VIDEO IN 1 audio inputs. Connect the left and right VIDEO

OUT audio outputs to the analog inputs on the VCR.

Optional Digital Audio: For a digital recording device, connect the digital

output of the recorder to one of the OPTICAL IN or COAXIAL IN digital

inputs on the receiver. Use the INPUT SETUP screen to assign that digital

input to the VIDEO source (VIDEO 1, 2, or 3) used for the previous

connections. If the recording device accepts a digital recording input,

connect one of the OPTICAL OUT or COAXIAL OUT connections to the

digital input of the recorder.

Connecting CD Player

See Figure 8

Connect the digital output of the CD player to any of the Optical or Coax

digital inputs on the receiver. Use the INPUT SETUP menu to assign the

digital input to the CD (the default is OPTICAL 1).

Optional: Connect the left and right analog outputs from the CD player

to the AUDIO IN jacks labeled CD (left and right). This option uses the

CD player’s D/A converters; however, this may result in an extra A/D

and D/A conversion step.

There are typically no video connections for a CD Player and no video

input is assigned to the CD, as a default setting.

Connecting Audio Recorder

See Figure 9

Connect the left and right analog outputs from an audio tape deck to the

VIDEO IN audio jacks (left and right).

Connect the Left/Right VIDEO OUT jacks to the inputs on the audio

tape deck.

Optional: For a digital recording device, connect the digital output of the

recorder to one of the OPTICAL IN or COAXIAL IN digital inputs on the

receiver. Use the INPUT SETUP screen to assign that digital input to an

audio source. If the recording device accepts a digital recording input,

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 50 51

Comments to this Manuals

No comments

Rotel RSX-1562 Owner's Manual Page 24

Comments to this Manuals

Related products and manuals for AV receivers Rotel RSX-1562