Rotel RDV-1092 Owner's Manual download pdf (Page 15)

1515

English

NTSC/PAL switch

There are two different standards for video

monitors: NTSC in US and Japan, PAL in Eu-

rope. The output of the RDV-1092 should be

set to match the standard your TV accepts.

Put the switch in the NTSC position for use

with NTSC video equipment. Put it in the PAL

position for the use with PAL equipment.

This switch only relates to the hardware con-

ﬁguration of your TV set and other compo-

nents. Regardless of the setting, the RDV-1092

can play DVD discs encoded in either format,

converting the signal to the format selected

with the NTSC/PAL switch.

NOTE: If your TV monitor can display both PAL

and NTSC signals, you can choose the “Auto

Format” setting in the conﬁguration menus.

This setting overrides the back panel switch;

the RDV-1092 displays the native format of

the disc being played (PAL or NTSC).

Other Connections

AC Power Input

It is best to plug the RDV-1092 directly into

a 2-pin polarized wall outlet. Avoid the use

of extension cords.

Your RDV-1092 will automatically conﬁgure

itself for the proper AC line voltage ranging

from 110 volts to 240 volts at 50/60Hz. No

setting is required to match the unit to your

local voltage.

Plug the supplied cord into the AC INPUT

receptacle on the back of the unit. After all

connections have been made, plug the cord

into an appropriate AC wall outlet.

NOTE: If you are away for an extended period

of time, it is a sensible precaution to unplug

your audio/video components.

EXT REM IN

The EXT REM IN receives IR command codes

relayed from an infrared receiver or from the

matching EXT REM OUT connector on Rotel

surround processors. This feature may be useful

when the unit is installed in a cabinet and its

front-panel IR sensor is blocked. Consult your

authorized Rotel dealer for information on IR

receivers and the proper wiring of a cable

with 3.5 mm plugs to ﬁt the connector.

12V TRIGGER Connection

The RDV-1092 can be activated by a remote

12 volt trigger signal from a Rotel surround

processor. The 12V TRIG input accepts any

control signal (AC or DC) ranging from 3

volts to 30 volts. When a cable is connected

to the input and a trigger signal is present,

the DVD player is activated. When the trig-

ger signal is interrupted, the unit goes into

standby mode. The front panel indicator light

remains lit, but the display goes dark and the

unit will not operate. Consult your authorized

Rotel dealer for information on the 12V TRIG

input and the proper wiring of a plug to ﬁt

the connector.

NOTE: When using the 12V Trigger, leave the

POWER button in the ON position.

Computer I/O

The RDV-1092 can be operated from a com-

puter with audio system control software

from third-party developers. This control is

accomplished by sending operating codes

from the computer via a hard-wired RS-232

serial connection.

The COMPUTER I/O input provides the neces-

sary network connections on the back panel.

It accepts standard RJ-45 8-pin modular plugs,

such as those commonly used in 10-BaseT

UTP Ethernet cabling.

For additional information on the connections,

cabling, software, and operating codes for

computer control of the RDV-1092, contact

your authorized Rotel dealer.

OVERVIEW

Basic controls for the RDV-1092 are on the

front panel. These controls are duplicated on

the remote control along with many more.

To guide you through the operation of the

RDV-1092, this section of the manual starts

with explaining the basic layout and function

of the front panel and the remote control. In

the following section, Using the RDV-1092,

we explain the features of the unit and how

to operate them.

Throughout this manual, numbers in gray

boxes refer to the RDV-1092 illustration (Fig-

ure 1) at the front of this manual. Letters refer

to the RR-DV98 remote illustration (Figure 2).

When both appear, the function is found on

both the RDV-1092 and the remote. When

only one appears, that function is found only

on the RDV-1092 or the remote.

On-Screen Display

The RDV-1092 displays menus, status in-

dicators, and interactive menus on the TV

monitor Many of these screens are used to

set up preferences and activate advanced

features of the unit. Others offer information

and choices useful during normal operation

of the unit.

NOTE: The default language for all RDV-1092

On-Screen Displays can be changed. See

the General Setup topic in the Setup section

of this manual.

Status Bar

During operation of the unit, a Status Bar

appears on the TV screen when the DISPLAY

button is pressed, when a setting is changed

or when the Top Menu or URD menus are

displayed:

DVD : play Ch : 1 00:01:22

ROTEL

Not Available

The left side of the Status Bar shows what type

of disc is playing. The top line shows the sta-

tus indicators such as NO DISC, LOADING,

PLAY, PAUSE, etc. along with CHAPTER and

TIME information. These information displays

are self-explanatory. The bottom line indi-

cates the new setting when an adjustment is

made or shows displays when attempting to

select an option that is not available for the

current disc.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 82 83

Comments to this Manuals

No comments

Rotel RDV-1092 Owner's Manual Page 15

Comments to this Manuals

Related products and manuals for DVD players Rotel RDV-1092