Rotel RC-06 User Manual download pdf (Page 8)

Phones Output 3

The Phones output allows you to connect

headphones for private listening. This output

accommodates standard stereo phone 3.5 mm

(1/8”) plugs. Plugging in a set of headphones

does not cut off the signal to the outputs. The

settings of the Function Selector and the Tape

Monitor Control determines which source is

heard. To listen to or monitor the component

connected to the Tape input set the Monitor

Control to the Tape position. For all other

inputs leave the Monitor Control in the Source

position and select the source you want to

listen to with the front panel Function Selector

or press the corresponding source button on

the remote control.

NOTE: Because the sensitivity of head-

phones and the other components in the

system can vary widely, always reduce the

volume level before connecting or discon-

necting headphones.

Media Player 4

A 3.5mm (1/8”) stereo input socket for a

“Media Player” is provided on the front of the

ampliﬁ er and is selected by setting the function

control to (AUX2). Any portable stereo cassette,

compact disc player or hard disc playback

device can be connected via this input. If

the device you are connecting has its output

via the headphone socket then note that you

must adjust the volume control on the player

for sound to be heard. Should the sound be

loud and distorted turn down the volume on

the player and if it is only just audible through

the speakers even when the ampliﬁ er volume

control is turned up fairly high then adjust the

volume control on the player.

NOTE:

When the 3.5mm (mimi jack) is inserted

into the Media Player socket the rear input called

AUX2 is disconnected. Removing the 3.5mm plug

from the Media player socket will allow the rear

AUX2 input to function.

Audio Controls

Volume Control

Turn the controls clockwise to increase the

volume, or counterclockwise to decrease the

volume. Or use the remote control volume but-

tons. Press the + button to increase the volume,

or the - button to decrease the volume.

Balance Control

The Balance Control adjusts the left-to-right

balance of the sound output. Normally the

control should be left in the center position.

In some situations, typically when the main

listening position is not ideally centered be-

tween the speakers, it may be necessary to

adjust the control to achieve proper left-to-right

balance. Turning the control counter-clockwise

shifts the sound balance to the left. Turning

the control clockwise shifts the sound balance

to the right.

Function Control

The Function control selects the input signal

source. Turn the Function control to the source

you want to listen to. Or press the corresponding

source button on the remote control.

The signal selected by the Function control is the

one you hear, as long as the Monitor control

is set to the Source postion. (See the following

section.) The signal selected by the Function

control also goes to the Tape Outputs.

Monitor Control

When the Monitor Control is set to the Source

position, the signal you hear, and which goes to

the Outputs, is selected by the Function Control.

To listen to the signal from a recorder connected

to the Tape Inputs, set the Monitor Control to

the Tape position. When the Monitor Control

is in the Tape position, the signal from the Tape

Input also goes to the Outputs.

The signal that goes to the Tape Output is always

selected by the Function Control. When you

are recording with a unit that has monitoring

capabilities, you can listen to the sound just

recorded by setting the Monitor Control to the

Tape position.

Mute Control

Remote Only

To temporarily mute the sound of the system

press the Mute Button on the RR-AT94 remote.

The volume Control LED blinks when the sound

is muted. Press the button again to return the

sound volume to the original level.

IR Inputs and Outputs

External Remote Input

This 3.5 mm mini-jack (labeled EXT REM IN)

receives command codes from an industry-

standard infrared receivers (Xantech, etc.)

located in the main listening room. This feature

is useful when the unit is installed in a cabinet

and the front-panel sensor is blocked. Consult

your authorized Rotel dealer for information

on external receivers and the proper wiring of

a jack to ﬁ t the mini-jack receptacle.

NOTE: The IR signals from the EXTERNAL

REMOTE IN jack can be relayed to source

components using external IR emitters or

hardwired connections from the IR OUT

jacks.

IR Output

The IR OUT jack sends IR signals received at the

EXTERNAL REM IN jack to an infrared emitter,

or to Rotel CD players, cassette decks, or tuners

with a compatible rear panel IR connector. This

allows you to use IR control features to oper-

ate other components when the IR sensors on

those components are blocked or obstructed

by installation in a cabinet.

See your authorized Rotel dealer for informa-

tion on IR repeater systems.

NOTE: The EXT REM IN jack located next

to the IR OUTPUT jack is for use with an

external IR sensor which duplicates the front

panel IR sensor.

RC-06 Stereo Control Amplifier

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 55 56

Comments to this Manuals

No comments

Rotel RC-06 User Manual Page 8

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Rotel RC-06