Rotel RC-06 User Manual download pdf (Page 6)

Remote Sensor

The Remote Sensor picks up the infrared

signals from the remote control. Do not cover

or block the sensor. It must be unobstructed or

the remote control will not work properly. The

operation of the Remote Sensor can also be

affected if it is exposed to bright light, particu-

larly sunlight. Certain types of lighting, such

as halogen lights, that emit a fair amount of

infrared light, can also interfere with proper

operation. In addition remote control functions

may not work reliably if the batteries in the

RR-AT94 are weak.

A Few Precautions

WARNING: To avoid potential damage to

your system, turn off ALL the components in

the system when connecting or disconnect-

ing the loudspeakers or any associated com-

ponents. Do not turn the system components

back on until you are sure all the connec-

tions are correct and secure. Pay particular

attention to the speaker wires. There must

be no loose strands that could contact the

other speaker wires, or the chassis of the

amplifier.

Please read this manual carefully. It provides

information on how to incorporate the RC-06

into your system as well as information that

will help you get optimum sound performance.

Please contact your authorized Rotel dealer

for answers to any questions you might have.

In addition, all of us at Rotel welcome your

questions and comments.

Save the RC-06 shipping carton and all en-

closed packing material for future use. Shipping

or moving the RC-06 in anything other than

the original packing material may result in

severe damage to your ampliﬁ er.

Fill out and send in the owner’s registration

card packed with the RC-06. Also be sure

to keep the original sales receipt. It is your

best record of the date of purchase, which

you will need in the event warranty service is

ever required.

Placement

Like all audio components that handle low-

level signals, the RC-06 can be affected by

its environment. Avoid placing the RC-06 on

top of other components. Also avoid routing

audio signal cables near power cords. This

will minimize the chance it will pick up hum

or interference.

The RC-06 generates heat as part of its normal

operation. The heat sinks and ventilation open-

ings in the ampliﬁ er are designed to dissipate

this heat. The ventilation slots in the top cover

must be open. There should be 10 cm (4 inches)

of clearance around the chassis, and reason-

able airﬂ ow through the installation location,

to prevent the ampliﬁ er from overheating.

Remember the weight of the ampliﬁ er when

you select an installation location. Make sure

that the shelf or cabinet can support it. We

recommend installing the RC-06 in furniture

designed to house audio components. Such

furniture is designed to reduce or suppress

vibration which can adversely affect sound

quality. Ask your authorized Rotel dealer for

advice about component furniture and proper

installation of audio components.

Cables

Be sure to keep the power cords, digital signal

cables and regular audio signal cables in

your installation away from each other. This

will minimize the chance of the regular audio

signal cables picking up noise or interference

from the power cords or digital cables. Using

only high quality, shielded cables will also help

to prevent noise or interference from degrad-

ing the sound quality of your system. If you

have any questions see your authorized Rotel

dealer for advice about the best cable to use

with your system.

AC Power and Control

AC Power Input

The RC-06 does not draw high levels of current

from the power outlet. However, whenever pos-

sible, it should be plugged directly into a 2-pin

polarized wall outlet. Do not use an extension

cord. A heavy duty multi-tap power outlet strip

may be used if it (and the wall outlet) can handle

the current demanded by the RC-06 and all

the other components connected to it.

Your RC-06 is conﬁ gured at the factory for the

proper AC line voltage in the country where

you purchased it (either 120 volts AC or 230

volts AC with a line frequency of either 50 Hz

or 60 Hz). The AC line conﬁ guration is noted

on a decal on the back panel.

NOTE: Should you move your RC-06

amplifier to another country, it is possible

to reconfigure it for use on a different line

voltage. Do not attempt to perform this

conversion yourself. Opening the enclosure

of the RC-06 exposes you to dangerous

voltages. Consult a qualified service person

or the Rotel factory service department for

information.

If you are going to be away from home for an

extended period of time such as a month-long

vacation, it is a sensible precaution to unplug

your ampliﬁ er (as well as other audio and video

components) while you are away.

Power/Standby Switch

and Power Indicator

The Power Indicator light above the Standby

button is lit whenever the RC-06 is connected

to a live AC outlet. When the front panel

Standby button or the remote control Power

button is pressed the RC-06 is turned on. When

the RC-06 is on the Function indicator and

the Volume control are illuminated. Pressing

either button again puts the RC-06 in standby

mode and turns off the Volume and Function

illumination.

See the “12V Trigger Outlet” section for more

information on ways you may be able to turn

on and off other components in your system

along with the RC-06.

RC-06 Stereo Control Amplifier

1 2 3 4 5 6 7 8 9 10 11 ... 55 56

Comments to this Manuals

No comments

Rotel RC-06 User Manual Page 6

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Rotel RC-06