Rotel RA-05 User Manual download pdf (Page 8)

Phones Output 4

The Phones output allows you to connect

headphones for private listening. This output

accommodates standard stereo phone (1/8”)

plugs. Plugging in a set of headphones does

not cut off the signal to the outputs. Use the

Speaker Selector to turn off the speakers. The

settings of the Function Selector and the Tape

Monitor Control determines which source is

heard. To listen to or monitor the component

connected to the Tape input set the Monitor

Control to the Tape position. For all other

inputs leave the Monitor Control in the Source

position and select the source you want to

listen to with the front panel Function Selector

or press the corresponding source button on

the remote control.

NOTE: Because the sensitivity of speakers

and headphones can vary widely, always

reduce the volume level before connecting

or disconnecting headphones.

Media Player 5

A 3.5mm (1/8”) stereo input socket for a

“Media Player” is provided on the front of the

ampliﬁer and is selected by setting the function

control to (AUX2). Any portable stereo cassette,

compact disc player or hard disc playback

device can be connected via this input. If

the device you are connecting has its output

via the headphone socket then note that you

must adjust the volume control on the player

for sound to be heard. Should the sound be

loud and distorted turn down the volume on

the player and if it is only just audible through

the speakers even when the ampliﬁer volume

control is turned up fairly high then adjust the

volume control on the player.

NOTE: When the 3.5mm (mimi jack) is inserted

into the Media Player socket the rear input called

AUX2 is disconnected. Removing the 3.5mm plug

from the Media player socket will allow the rear

AUX2 input to function.

Audio Controls

Volume Control

-f

Turn the controls clockwise to increase the

volume, or counterclockwise to decrease the

volume. Or use the remote control volume but

tons. Press the + button to increase the volume,

or the – button to decrease the volume.

Balance Control

The Balance Control adjusts the left-to-right

balance of the sound output. Normally the

control should be left in the center position.

In some situations, typically when the main

listening position is not ideally centered be

tween the speakers, it may be necessary to

adjust the control to achieve proper left-to-right

balance. Turning the control counter-clockwise

shifts the sound balance to the left. Turning

the control clockwise shifts the sound balance

to the right.

Tone On/Off Switch

When the Tone Switch is in the Off position the

Bass and Treble Control (Tone Control) circuits

are bypassed to ensure the purest possible

sound. Leave the Tone Switch in the Off posi

tion unless you want to use the Tone Controls.

Turn the Tone Switch to the On position if you

want to adjust the Tone Controls.

Bass and Treble Controls

When the Tone Switch is in the On position,

turning the Bass and Treble Controls adjusts the

tone balance of the sound. Turn the Controls

clockwise to increase the bass or treble output.

Turn the Controls counterclockwise to decrease

the bass or treble output.

A properly set up high-performance audio

system produces the most natural sound with

little or no adjustment of the tone controls. Use

these controls sparingly. Be particularly careful

when turning the controls up (clockwise). This

increases the power output in the bass or treble

range, increasing the load on the ampliﬁer

and speakers.

Function Control

w d

The Function control selects the input signal

source. The signal selected by the Function

control is the one you hear, as long as the

Monitor control is set to the Source postion.

(See the following section.) The signal selected

by the Function control also goes to Preamp

Outputs and the Tape Outputs. Turn the front

panel Listening Selector to the source you want

to listen to. Or press the corresponding source

button on the remote control.

Monitor Control

When the Monitor Control is set to the Source

position, the signal you hear, and which goes

to the Preamp Outputs, is selected by the

Function Control. To listen to the signal from a

recorder connected to the Tape Inputs, set the

Monitor Control to the Tape position. When

the Monitor Control is in the Tape position,

the signal from the Tape Input also goes to the

Preamp Outputs.

The signal that goes to the Tape Output is always

selected by the Function Control. When you

are recording with a unit that has monitoring

capabilities, you can listen to the sound just

recorded by setting the Monitor Control to the

Tape position.

Mute Control

Remote Only

To temporarily mute the sound of the system

press the Mute Button on the RR-AT94 remote.

The volume Control LED blinks when the sound

is muted. Press the button again to return the

sound volume to the original level.

IR Inputs and Outputs

External Remote Input

[

This 3.5 mm mini-jack (labeled EXT REM IN)

receives command codes from an industry-

standard infrared receiver (Xantech, etc.)

located in the main listening room. This feature

is useful when the unit is installed in a cabinet

and the front-panel sensor is blocked. Consult

your authorized Rotel dealer for information

on external receivers and the proper wiring of

a jack to ﬁt the mini-jack receptacle.

NOTE: The IR signals from the EXTERNAL

REMOTE IN jack can be relayed to source

components using external IR emitters or

hardwired connections from the IR OUT

jacks.

IR Output

]

The IR OUT jack sends IR signals received at the

EXTERNAL REM IN jack to an infrared emitter,

or to Rotel CD players, cassette decks, or tuners

with a compatible rear panel IR connector. This

allows you to use IR control features to oper

ate other components when the IR sensors on

those components are blocked or obstructed

by installation in a cabinet.

See your authorized Rotel dealer for informa

tion on IR repeater systems.

NOTE: The EXT REM IN jack located next to

the the IR OUTPUT jack is for use with an

external IR sensor which duplicates the front

panel IR sensor.

RA-05 Stereo Integrated Amplifier

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 51 52

Comments to this Manuals

No comments

Rotel RA-05 User Manual Page 8

Comments to this Manuals

Related products and manuals for Receivers and Amplifiers Rotel RA-05