Rotel RDV-1040 User Manual download pdf (Page 9)

English

Connecting the Power Cord

AC Input

Your RDV-1040 is configured at the factory for

the proper AC line voltage in the country where

you purchased it (USA: 115 volts/60Hz AC

or CE: 230 volts/50Hz AC). The AC line con-

figuration is noted on a decal on the back of

your unit.

After all the audio/video connections have been

made, plug the supplied power cord into the

AC INPUT receptacle on the back of the unit.

Then insert the power plug into an AC wall

outlet. The STANDBY indicator lights and setup

is complete. Note that a small amount of power

(3 watts) is always used while the power cord

is connected to the wall outlet.

Observe the following precautions:

• Do not connect or disconnect the power cord

with wet hands.

• Disconnect the power cord if you are not

going to use the unit for a long time.

• When unplugging the player from the wall

outlet, always pull the plug, not the power

cord.

• Disconnect the power cord before cleaning

the unit.

• Disconnect the power cord before moving

the unit.

• Do not damage, alter, twist or pull the power

cord. This may damage the cord and cause

fire, electric shock, or other accidents. Con-

tact your authorized Rotel dealer and get

a new power cord if the cord is damaged.

• Do not put anything heavy, on the unit, or

the power cord, as this may cause fire, elec-

tric shock, or other accidents.

RR-DV96 Remote Control

Installing the Batteries

The battery compartment is located on the back

of the remote control unit.

1 Press down on the

point shown by

the arrow at the

top of the com-

partment cover,

and pull up the

cover.

2 Place two R6P (SUM-3)/

AA(15F) batteries in the re-

mote control according to

the polarity markings (“+”

and “–”) inside the com-

partment and on the bat-

teries.

3 Place the cover

over the com-

partment, and

press down

lightly.

The batteries will last

about six months with normal use. If the func-

tions of the remote control become erratic, re-

place the batteries.

Precautions for the safe use of

batteries

Observe the following precautions for the safe

use of batteries. If they are used improperly

their life will be shortened, they may burst or

their contents may leak.

• Remove the batteries from the remote con-

trol if it will not be used for a long period

of time.

• Remove dead batteries and dispose of them

properly.

• Never leave dead batteries lying around.

Do not take them apart, mix them with other

refuse, or throw them into an incinerator.

• Never touch liquid that has leaked out of a

battery.

• Do not mix new and old batteries, or bat-

teries of different types, when replacing them.

Programming the RR-DV96

Remote to Control a TV

After it is programmed the RR-DV96 can op-

erate your TV set.

1 Set the TV/DVD switch

to TV.

2 Press and hold down the TV/VIDEO-CAN-

CEL

button. Then enter the manufac-

turer code of your TV listed in the following

table using the numeric buttons (0 - 9)

Do not release TV/VIDEO-CANCEL. button

until the next step is completed. (Example:

To enter code “01” press and release the

“0” button, then press and release the “1”

button.

3 Press the ENTER

button, then release

the TV/VIDEO-CANCEL button.

Manufacturer No.

Aiwa 36

Beijing 22

CCE 02

Changhong 34

Daewoo 17, 37

Ferguson 27

Finlux 30

Funai 32

Gradiente 15, 20

Grundig 19

Hitachi 10

ITT 28

Jinxing 38

JVC 01, 23,

24, 25

Konka 40

LG (Goldstar) 18

Magnavox 02

Mitsubishi 03

Mivar 29

Manufacturer No.

NEC 20

Noblex 22

Nokia 31

Panasonic 04, 11

Peony 34, 38,

Philco 10, 17,

Philips 02

RCA 05

Samsung 12, 33,

34, 35

Sanyo 13, 16

Sears 13

Sharp 06

Sony 07

TCL 41

Thomson 26

Toshiba 08, 14

Zenith 09

4 Test the program setting by pressing the TV

POWER

button to see if it turns your

set on. If there is more than one code listed

for the manufacturer of your TV, try them

one by one until you succeed.

Remote Control TV Operation

When the TV/DVD switch

is in the TV po-

sition the following buttons can be used to con-

trol the TV.

TV POWER

Turns the TV on or off.

CH+ and CH –

31 13

Changes the TV channels.

VOL+ and VOL –

32 12

Adjusts the TV volume.

TV/VIDEO button

Switches the TV input between TV and Video.

0 - 10 and (Numeric Buttons)

Selects the TV channels. Note: For some TVs,

pressing “+10” functions as the “+100”. The

“10” button functions as ENTER if your TV re-

quires pressing the ENTER after selecting a

channel number.

MUTING button

Mutes the TV sound.

External Remote In

The 3.5mm mini-jack (labeled EXT REM IN) re-

ceives command signals from an industry stan-

dard infrared receiver. This feature is useful

when the unit is installed in a cabinet and the

front panel sensor is blocked. Consult your au-

thorized Rotel dealer for information on ex-

ternal receivers and the proper wiring of a jack

to fit the mini-jack receptacle.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 30 31

Comments to this Manuals

No comments

Rotel RDV-1040 User Manual Page 9

Comments to this Manuals

Related products and manuals for DVD players Rotel RDV-1040