Rotel RCX-1500 Owner's Manual download pdf (Page 20)

RCX-1500 Stereo Compact Disc Receiver

Remote Unit Advanced Buttons

Setup menu

To enter the setup menu, press the SETUP button on the remote control

and you will see the following display:

> 1 POWER OPTION

2 DIMMER

3 FACTORY DEFAULT

4 VERSION

5 ANTENNA SELECT

6 POWER ON VOLUME

7 EXIT

POWER OPTION, There are two choices for powering up, NORMAL

and QUICK. When set to NORMAL (Default) the unit consumes less

power during standby mode but takes a longer time to resume operation.

When set to QUICK, normal operations are started immediately after

power on.

DIMMER controls the brightness of the front panel display, it can be

dimmed with seven steps. You can access this control directly with the

DIM button on the remote control.

FACTORY DEFAULT sets the RCX-1500 into the original state as when it

left the factory. Presets and network conﬁgurations will be lost, and puts

the RCX-1500 into remote code 1 (see below).

VERSION shows this unit’s version.

ANTENNA SELECT choose AUTO(default), FM or DAB antenna.

POWER ON VOLUME, sets the volume level each time the unit is

powered on.

EXIT returns to previous menu.

Second Remote Code

The RCX-1500 is set from the factory to operate with remote code 1. If

you ﬁnd that the RCX-1500 remote is conﬂicting with other Rotel products,

you can set the RCX-1500 and the remote control to remote code 2 with

the following steps:

1, While pointing the remote at the RCX-1500, press on the remote

control ‘FM’ dand ‘2’ keys at the same time. Release the ‘FM’ key and

continue to press the ‘2’ key for 5 seconds. The RCX-1500 will show

‘Audio Custom Code 1--> 2’.

2, Repeat the above procedure and press ‘1’ key instead of ‘2’ to change

the unit back to Code 1.

3. The RCX-1500 remote keys, such as PLAY, STOP, PAUSE, use Rotel’s

standard codes for CD players. If you ﬁnd that this is conﬂicting with

your Rotel CD player, press ‘CD’ and ‘2’ keys at the same time. Release

‘CD’ key and continue to press ‘2’ key for 5 seconds. The RCX-1500

will show ‘CD Custom Code 1 --> 2’.

4. Repeat step 3 above and press ‘1’ key instead of ‘2’ to change the

unit back to Code 1.

Troubleshooting

Most difﬁculties in audio systems are the result of incorrect connections,

or improper control settings. If you encounter problems, isolate the area

of the difﬁculty, check the control settings, determine the cause of the fault

and make the necessary changes. If you are unable to get sound from the

RCX-1500, refer to the suggestions for the following conditions:

Standby Indicator Is Not Lit

The Standby Indicator should be lit whenever the RCX-1500 is plugged

into the wall power outlet. If it does not light, test the power outlet with

another electrical device, such as a lamp. Be sure the power outlet being

used is not controlled by a switch that has been turned off.

Network Does Not Work

If you have trouble connecting the RCX-1500 to your wireless network,

check your network setting carefully, these steps may help to resolve the

problem.

1. Conﬁrm that a Wi-Fi network is available. Check that other computers

can access the Internet using the same network.

2. Check that a DHCP server is available, or that you have conﬁgured a

static IP address on the unit. Please refer to Network Conﬁg section.

3. Check that your network’s ﬁrewall is not blocking any outgoing

ports.

4. Do a hard power off (unplug the AC mains) and let the unit restart

the network scanning cycle.

5. Make sure the RCX-1500 can receive the WiFi signal in its location.

Use an USB extension cord to move the WiFi dongle up higher or to a

different location to maximize reception.

No Sound

1. Check the cables between the RCX-1500 output and loudspeakers,

be sure they are connected properly. Refer to Fig. 2.

2. Music played from Internet Radio stations are affected by the speed

of your internet connection. If you ﬁnd that music is cutting out regularly,

contact your internet service provider.

3. Make sure the station you selected is operating at the current hour.

The station can be broadcasting from a different time zone.

4. Please insert the Wi-Fi dongle (or wired adaptor) to the ethernet port

on the rear panel even if no networks are available. After power ON,

the unit will look for available networks before allowing the user to access

FM and DAB features.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 73 74

Comments to this Manuals

No comments

Rotel RCX-1500 Owner's Manual Page 20

Comments to this Manuals