Rotel RTC-965 Owner's Manual download pdf (Page 4)

English

Step Four: Store the code number by pressing the corre-

sponding DEVICE button again. The button will blink

twice to confirm the storage of the code in memory.

Step Five: Test the COMMAND buttons, using the tables

as a reference for the available functions. If the functions

do not work correctly, repeat the above steps, with the

next available 3-digit code from the list for your brand of

component.

Repeat the steps above for each of up to eight compo-

nents, assigning each one to the appropriate DEVICE key.

Auto-Search Programming

If the code table does not provide a 3-digit code or if

none of the code numbers assigned to your brand of

component work, use the following auto-search method

to find a code number that will operate your components.

Step One: Turn on the component you wish to operate.

Step Two: Press the corresponding DEVICE button and

the MUTE button, simultaneously for one second or

more. The LED will light for 20 seconds.

Step Three: Press and hold the CH UP or CH DOWN but-

ton. This sends a succession of Power ON/OFF code sig-

nals that are stored in memory. Stop pressing the CH

button as soon as the component turns off, signifying that

you have found a code set that operates that component.

Step Four: Press the DEVICE button to store the code set

you have found. The button will blink twice to confirm

that you have stored the code.

Step Five: Test the remote control functions. If any do not

work properly, repeat the preceding steps until you find

the right code.

RR-949

Light Button

The LIGHT button turns on backlighting so you can see

the buttons in a dark room. The lights stay on for 7 sec-

onds and will stay on for an additional 7 seconds each

time another button is pressed.

Programming

The RR-949 can replace up to eight different remote con-

trols, one for each of the eight DEVICE buttons. Before

you use it, you must program the RR-949, i.e. tell it which

audio/video components you wish it to control.

The RR-949 contains hundreds of command sets for vari-

ous A/V components. Programming the remote involves

selecting the command sets that correspond to the com-

ponents in your system, and assigning them to the eight

DEVICE buttons by entering a three digit code. This need

only be done once during initial set-up of the RR-949.

The easiest way to proceed is to find your components

and corresponding three-digit codes from the list of

codes supplied with this manual. If your component is

not listed, there is an alternative auto-search method for

finding the right command set.

Three Digit Code Programming

Find your audio/video component in the code list and

note the 3-digit code(s):

Step One: Turn on the component you wish to memorize.

Step Two: Press the corresponding DEVICE button (for

example, if you are memorizing the command set for a

CD player, press the CD DEVICE button at the top of the

RR-949). While pressing the DEVICE button, simulta-

neously press the MUTE button and hold both for at least

one second. The DEVICE key will light in red for 20 sec-

onds, indicating that you have entered the program

mode. The next step must be done within this 20 second

period, or the RR-949 will revert to its standard operating

mode.

Step Three: Point the RR-949 at the audio/video compo-

nent and enter the 3-digit code, using the numeric but-

tons. The DEVICE key will flash each time you enter a

digit. If you have entered the correct code, the compo-

nent will turn off. If there is more than one 3-digit code

for your brand of source component, continue entering

additional 3-digit codes from the list until the component

turns off, indicating that you have found the right one.

1 2 3 4 5 6 7 8 9 ... 13 14

Comments to this Manuals

No comments

Rotel RTC-965 Owner's Manual Page 4

Comments to this Manuals

Related products and manuals for Audio amplifiers Rotel RTC-965